OpenVZ 平台 Google BBR Rinetd 方式 加速 TCP

Linux 星雨 4765℃ 0评论

简介

ubuntu-16.04-x86_64 亲侧,效果非常好,极其稳定

手动搭建

仅支持 64 位系统。

1.下载文件到 /usr/bin/rinetd-bbr

wget -O /usr/bin/rinetd-bbr https://github.com/linhua55/lkl_study/releases/download/v1.2/rinetd_bbr_powered

2.设置权限

chmod a+x /usr/bin/rinetd-bbr

3.创建配置文件

vi /etc/rinetd-bbr.conf

输入以下内容

# bindadress bindport connectaddress connectport
0.0.0.0 443 0.0.0.0 443

其中的 443 请改为你的端口
IP 地址统一写 0.0.0.0

4.获取接口名称

#
 ip addr
1: lo:  mtu 65536 qdisc noqueue state UNKNOWN
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: venet0:  mtu 1500 qdisc noqueue state UNKNOWN
    link/void
    inet 127.0.0.2/32 scope host venet0
    inet 10.10.10.10/32 brd 10.10.10.10 scope global venet0:0

看具有公网 IP 的接口名称(比如我的公网 IP 是 10.10.10.10),上面这种的接口是 venet0:0 而不是 venet0
OpenVZ 应该都是 venet0:0 接口。

5.启动

/usr/bin/rinetd-bbr -f -c /etc/rinetd-bbr.conf raw venet0:0 &

注意:将最后的接口改为你上面获取到的接口。在命令最后面加 & 以使其能后台运行。
验证

正常情况下的输出:

[    0.000000] Linux version 4.10.0+ (root@gcc) (gcc version 4.9.4 (Ubuntu 4.9.4-2ubuntu1~14.04.1) ) #1 Mon Jul 31 04:50:50 UTC 2017
[    0.000000] bootmem address range: 0x7f2acc000000 - 0x7f2acffff000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16159
[    0.000000] Kernel command line:  virtio_mmio.device=268@0x1000000:1
[    0.000000] PID hash table entries: 256 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Memory available: 64492k/0k RAM
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:4096
[    0.000000] lkl: irqs initialized
[    0.000000] clocksource: lkl: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns
[    0.000001] lkl: time and timers initialized (irq2)
[    0.000003] pid_max: default: 4096 minimum: 301
[    0.000021] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
[    0.000023] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
[    0.009053] console [lkl_console0] enabled
[    0.009056] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.009128] NET: Registered protocol family 16
[    0.009265] clocksource: Switched to clocksource lkl
[    0.009324] NET: Registered protocol family 2
[    0.009418] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.009421] TCP bind hash table entries: 512 (order: 0, 4096 bytes)
[    0.009503] TCP: Hash tables configured (established 512 bind 512)
[    0.009971] UDP hash table entries: 128 (order: 0, 4096 bytes)
[    0.009976] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[    0.010060] virtio-mmio: Registering device virtio-mmio.0 at 0x1000000-0x100010b, IRQ 1.
[    0.010186] workingset: timestamp_bits=62 max_order=14 bucket_order=0
[    0.010203] virtio-mmio virtio-mmio.0: Failed to enable 64-bit or 32-bit DMA.  Trying to continue, but this might not work.
[    0.010350] NET: Registered protocol family 10
[    0.010849] Segment Routing with IPv6
[    0.010859] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    0.010993] Warning: unable to open an initial console.
[    0.011006] This architecture does not have kernel memory protection.
[    2.169284] random: fast init done

查看 iptables 规则:

# iptables -t raw -nL
Chain PREROUTING (policy ACCEPT)
target     prot opt source               destination
ACCEPT     tcp  --  0.0.0.0/0            0.0.0.0/0            tcp dpt:443 /* LKL_RAW */
DROP       tcp  --  0.0.0.0/0            0.0.0.0/0            tcp dpt:443 /* LKL_RAW */
Chain OUTPUT (policy ACCEPT)
target     prot opt source               destination

已经有两条规则了。

转载请注明:星雨小站 » OpenVZ 平台 Google BBR Rinetd 方式 加速 TCP

如果你觉得这篇文章对你有帮助,请支持我继续更新网站!捐赠本站
喜欢 (1)or分享 (0)
发表我的评论
取消评论
表情

Hi,您需要填写昵称和邮箱!

  • 昵称 (必填)
  • 邮箱 (必填)
  • 网址